Selection of Jinan color steel plate: good bearing capacity; Beautiful appearance; Large plate utilization coefficient, convenient connection mode, and the wave distance and waveform in line with the domestic mode are preferred. With factory certificate and product quality certificate, and indicate the product standard number, steel plate number, galvanized quantity, surface structure, surface quality, specification and dimension, shape accuracy, etc.

竖向布置墙板。Wall panels shall be arranged vertically.

竖向布置墙板时，宜采用带形窗，这样的隔断可以减少洞口结构，有利于防雨。使用单面窗户时，窗户两侧结构复杂，施工不容易出现漏雨现象，板材排布时选用排版起始线，板材排列与开口尺寸协调，横向布置墙板时，主要解决窗面两侧结构复杂，施工不容易出现漏雨现象，板材排版时选用开式起线。

When the wallboard is vertically arranged, the strip-shaped window should be adopted. Such partition can reduce the portal structure and is conducive to rainproof. When the window is constructed, the size of the opening plate is not coordinated with that of the opening plate. When the opening plate is used for construction, it is easy to be leaked. When the opening plate is used for drainage, it is easy to be arranged on both sides. When the opening plate is used for construction, it is easy to be leaked. When the opening plate is used for drainage, the size of the opening plate is not coordinated with that of the window.

彩板墙的长度包括：从檐口的封闭标高到墙底的起始高度；从檐口的封闭高程到洞口上方表面的高度；从洞口下面到洞口的上表面的高度，从洞口下表面到墙底的起始高度等三种，因此在确定板长之前，必须确定檐口、窗、门洞和其他洞口的高程和结构做法，并以此来布置墙面檩条的位置，从而计算墙面板的长度，一般情况下，由于对其美观要求的要求，彩板墙面在垂直布置时不宜采用这种方法。如墙高较大，才考虑采用搭接法，此时墙面的长度应加上搭接长度。山墙檐口为斜截面时，每一板的坡度计算其大值。

The length of the color board wall includes: from the closed elevation of the cornice to the starting height of the wall bottom; The height from the enclosed elevation of the cornice to the surface above the opening; The height from the lower part of the opening to the upper surface of the opening and the starting height from the lower surface of the opening to the bottom of the wall. Therefore, before determining the plate length, the elevation and structural method of cornice, window, door opening and other openings must be determined, so as to arrange the position of wall purlin, so as to calculate the length of wall panel. Generally, due to the requirements of its aesthetic requirements, This method should not be used when the color plate wall is vertically arranged. If the wall height is large, the overlapping method shall be considered. At this time, the length of the wall shall be added with the overlapping length. When the gable cornice is of oblique section, the maximum value shall be calculated according to the slope of each board.

横向设置壁板。Set wall panels horizontally.

侧向布置墙板主要用于夹芯板，有时也用于单层压型板。这种方法以板宽为模组垂直布置。当设计时，大于板宽的孔时，尽量将孔的上、下边缘与板的横向接缝组合在一起，以免造成结构复杂，横向布置墙板多与柱的中轴线分开，首、末柱之间的板长为柱距尺寸，再加上首末柱的轴线长度为柱距尺寸，中间墙板的长度为柱距尺寸，以及柱轴线的长度为柱距尺寸等。根据坡度不同，斜坡出的板长。

The side wall panels are mainly used for sandwich panels and sometimes single-layer profiled panels. This method takes the board width as the vertical layout of the module. In the design, when the hole is larger than the plate width, try to combine the upper and lower edges of the hole with the transverse joint of the plate, so as not to cause complex structure. The transverse wall plate is mostly separated from the central axis of the column. The plate length between the head and end columns is the column spacing dimension, plus the axis length of the head and end columns is the column spacing dimension, and the length of the middle wall plate is the column spacing dimension, And the length of the column axis is the column spacing size, etc. According to the slope, the length of the slab from the slope is different.

无绝缘板连接。No insulation board connection.

非绝热板连接有两种：显露连接和隐式连接。当接合时，将接合的紧固件连接到接缝处，接合处与墙梁连接。这样的联接，使扣件头部在墙面凹陷处更美观。当某些波距较大时，连接紧固件也可设置在峰顶。隐接板覆盖面较窄，将块板与墙面连接后，将第二块板插入块板的板边槽，起到抗负风压的作用。

There are two types of non adiabatic plate connection: exposed connection and implicit connection. When joining, connect the joined fasteners to the joint, and the joint is connected with the wall beam. Such connection makes the fastener head more beautiful in the concave part of the wall. When some wave distances are large, the connecting fasteners can also be set at the peak. The coverage of the concealed board is narrow. After connecting the first board with the wall, insert the second board into the side groove of the first board to resist negative wind pressure.

夹板联接。Splint connection.

夹芯板墙板的连接方式有工字铝连接、插座连接和暗扣连接。

The connection modes of sandwich panel wall panel include I-shaped aluminum connection, socket connection and concealed buckle connection.彩钢墙体基础结构。

Color steel wall foundation structure.

墙体基础结构主要解决防止雨水渗入室内的问题。为防止墙面留下的雨水渗入室内，连接处的地板和矮墙顶部混凝土浇筑成高达60毫米的彩色钢板混凝土框架。

The wall foundation structure mainly solves the problem of preventing rainwater from penetrating into the room. In order to prevent the rainwater left by the wall from penetrating into the room, the floor at the connection and the top of the low wall are concreted into a colored steel plate concrete frame up to 60mm.