楼承板在厂家生产加工制造时如果在钢柱处没有连接，因此需要安装连接钢筋、遍布钢筋和附加钢筋。那么济南楼承板增加钢筋连接有什么事项了解呢？下面一起来了解一番。

　　If there is no connection in the steel column when the floor bearing plate is manufactured by the manufacturer, it is necessary to install connecting steel bars, all over steel bars and additional steel bars. So what matters do you know about the reinforcement connection of ji 'nan floor bearing plate? Let's take a look.

　　用同等级、同型号同直径的钢筋套上钢架，然后拧下来，把外绑扎断电焊。还要保证连接好后，还要检查对面两侧的钢桁架是否在同一水平面上。

　　With the same grade, the same model with the same diameter of the steel frame, and then screwed down, the external binding broken welding. Once connected, check that the opposite steel trusses are on the same level.

　　附加钢筋的电焊需要单层焊接，焊接长度为10d，避免钢桁架侧边错位。设计图纸应注明预埋孔，并在孔周围设置肋板。当楼承板遇到钢梁须在现场进行激光切割而平面外观发生变化时，激光切割位置损坏也需要设置肋板，并用橡胶修复伤口。

　　The electric welding of additional steel bars requires single-layer welding with a welding length of 10d to avoid side dislocation of steel trusses. The design drawings shall indicate the embedded holes and provide ribs around the holes. When the floor bearing plate meets the steel beam, it must be cut by laser on site and the appearance of the plane changes. When the laser cutting position is damaged, it is necessary to set up the rib plate and repair the wound with rubber.

　　在钢筋板的深层钢桁架橡胶支座中，每边不得小于断承钢筋总面积的一半且不小于212。垂直钢桁架楼承板定向加水桁架上链墙的面筋，额外的水加固墙*混凝土加固盖须确保至少15毫米。

　　In the deep rubber bearings of steel trusses of reinforced plates, each side shall not be less than half of the total area of broken reinforcement and not less than 212. Vertical steel truss floor bearing plate orientated water truss upper chain wall of gluten, additional water reinforcement wall * concrete reinforcement cover shall ensure at least 15 mm.

　　在粘贴钢筋的过程中，应特别注意对已铺设好的楼承板的保护，更不要在热镀锌板上行走或踩踏。禁止旋转和断开钢桁架：如果须断开，应使用通信型号和规格的钢筋将钢桁架重新连接到钢桁架上。

　　In the process of sticking steel bar, special attention should be paid to the protection of the floor bearing plate has been laid, not to walk or trample on the hot galvanized plate. Do not rotate and disconnect steel trusses: if disconnection must be made, the steel trusses should be reattached to the steel trusses using rebar of communication type and specification.

　　济南楼承板附加钢筋工程及管道铺设：

　　钢筋板连接钢筋、橡胶承重钢筋及与钢筋桁架楼板垂直夹角的钢筋必须按设计规定设置。并用钢桁架绑扎，并用双丝双扣扎牢。链条钢筋的下部或上下钢筋应放置在钢桁架暗钢筋的上侧。钢筋桁架总面积的一部分铺装完毕后，需要立即将钢筋橡胶支座与钢筋与钢筋桁架垂直角连接的钢筋绑扎，以保证钢筋板连接为一个整体。由于钢桁架楼板的危害，楼板内的管材应正确选择。

　　Additional reinforcement engineering and pipeline laying of Jinan floor bearing plate:

　　The steel bar connecting the steel plate, the rubber bearing steel bar and the steel bar with the vertical Angle of the steel bar truss floor must be set according to the design provisions. And steel truss binding, and double wire double buckle binding. The lower or upper steel bars of the chain shall be placed on the upper side of the concealed steel bars of the steel truss. After paving part of the total area of the steel truss, it is necessary to bind the steel rubber bearing with the steel bar and the steel bar truss at vertical angles to ensure that the steel plate is connected as a whole. Due to the harm of steel truss floor, the pipe in the floor should be chosen correctly.

　　楼承板增加钢筋连接有什么事项了解？ 总之，在进行增加钢筋链接的过程中需要操作人员正确的使用方法方式以及步骤，避免危险隐患发生。更多内容就来网站www.jnhxtcg.com咨询吧！

　　What matters do you know about the reinforcement connection of the floor bearing plate? In short, in the process of increasing the reinforcement link, the operator needs to use the method and steps correctly to avoid the occurrence of danger and hidden dangers. More content to the website www.jnhxtcg.com consultation!