我们知道，在建设项目开始之前，须有一个通用框架。毕竟，该框架承受了整个建筑物的重量，代表了建筑物的质量。主梁是非常关键的部分，主梁的常见材料应用是增强的地板承重板。也就是说，如果地板承压板的施工有问题，则主梁的使用将不好。不可能进行下一个施工，下面来讲讲济南楼承板施工时对主梁搭建的要求。

We know that there must be a general framework before a construction project starts. After all, the frame bears the weight of the whole building and represents the quality of the building. The main beam is a very critical part, and the common material application of the main beam is the reinforced floor bearing plate. In other words, if there is a problem in the construction of the floor pressure plate, the use of the main beam will not be good. It is impossible to carry out the next construction. Let's talk about the requirements for main beam construction during the construction of Jinan floor bearing plate.

加固楼承板的承重梁与主墙两端的支点相连，因此工字钢的结构应合理，这是整个结构施工中受力较大的部分。楼承板主梁的搭接工艺应首先移去预埋钢板的位置，对找平层的水泥墙表皮进行平整，然后再固定预埋钢板，同时基本与框架的施工过程保持一致，楼承板的主梁的测量非常重要，应进行一梁一测量，误差不得超过4mm。

The bearing beam of the reinforced floor bearing plate is connected with the fulcrum at both ends of the main wall, so the structure of I-steel should be reasonable, which is the part with greater stress in the whole structure construction. The lapping process of the main beam of the floor support plate should first remove the position of the embedded steel plate, level the cement wall skin of the leveling layer, and then fix the embedded steel plate. At the same time, it is basically consistent with the construction process of the frame. The measurement of the main beam of the floor support plate is very important, and it should be measured one beam at a time, with an error of no more than 4mm.

当主梁重叠时，应进行点焊，补强和全焊。主梁的两端应进行360度焊接，工字钢应以相同的应力垂直放置。角钢与加强型楼承板的主梁连接，以形成一个整体且均匀的力。角钢的连接要求如下：

When the main beams overlap, spot welding, reinforcement and full welding shall be carried out. Both ends of the main beam shall be welded 360 degrees, and the I-beam shall be vertically placed with the same stress. The angle steel is connected with the main beam of the reinforced floor bearing plate to form an integral and uniform force. The connection requirements of angle steel are as follows:

根据钢结构中异种钢的连接规范，切去角钢插入部分的上开口，焊接点的凸部用角磨机抛光并弄平，以使板光滑而不会发出声音。插入点部分已完全焊接，并且误差扩大了膨胀和收缩的尺寸。不应大于3mm。焊接后，它应该是水平和垂直的，并且层应该是水平的。

According to the connection specification of dissimilar steel in steel structure, the upper opening of the angle steel insertion part shall be cut off, and the convex part of the welding point shall be polished and leveled with an angle grinder to make the plate smooth without sound. The insertion point portion has been completely welded and the error enlarges the dimensions of expansion and contraction. Shall not be greater than 3mm. After welding, it should be horizontal and vertical, and the layer should be horizontal.

在安装加固楼承板之前，主梁的架设是关键的施工环节，要求操作人员始终注意施工情况。一旦发现施工不正确，应立即停止施工，并按照正确的方法进行调整，以尽可能避免因错误引起的错误，从而使楼承板安装更加智能化链接不好。

Before the installation and reinforcement of the floor support plate, the erection of the main beam is a key construction link, and the operators are required to always pay attention to the construction situation. Once the construction is found to be incorrect, the construction shall be stopped immediately and adjusted according to the correct method to avoid errors caused by errors as much as possible, so as to make the installation of floor bearing plates more intelligent and link poorly.

当然，操作人员还需要学习更多的施工方法和方法，切记注意事项，很为详细的注意事项或者其他方面的问题，您都可以关注我们网站http://www.jnhxtcg.com咨询联系我们！

Of course, operators also need to learn more construction methods and methods, remember precautions, very detailed precautions or other problems, you can follow our website http://www.jnhxtcg.com Contact us!